How to Install a Garage Door Opener

If you already have an opener mounted in your garage and you want to change it, then take all components down and discard all of them. yes, you require to toss out the old buttons, remotes and also the electrical wiring (unless it is on top of the drywall of the garage). Your new opener, with few exceptions, will certainly come with all repairs including wall surface button, 2 remotes and potentially also an outside installed button with switches where you can enter a personal code and open and shut the garage door. This is an excellent attribute for your youngsters when they get home from college and need to get to the house. Today’s most current versions often are constructed with digital coding that changes the code sent from your remote to the door opener unit in the garage each time you utilize the device. If you need to have Cleveland garage door opener installation, you should find a quality expert that can help you most.

Next, I would unpack all the parts being sure that all parts are present in package. Separate the various packages of equipment and READ the guidelines. They will certainly save you time in the future.

Among the first things you’ll be ask to do is to construct the track. It usually comes in 3 areas. It’s simple to put together and hook to the front of the opener. Follow your particular directions.


More than most likely the next point you’ll be ask to do when reviewing your directions is to install the door opener to the ceiling of your garage. This is where the 7 foot action ladder will certainly aid in this treatment. Utilize it to hold the opener in the approximate area while making the securing that is required. It is sometimes possible now to include an easy rubber system in between the mounting equipment and the drywall. If correctly done, this will substantially lower a feasible vibration.

Connect the “door end” of the opener to the door header (usually 2 x 12 or something similar) that is above the whole size of the garage door. Lag bolts are generally utilized to accomplish this. Right about now you should have currently set up the chain or the belt that relocates when the door opener motor transforms a sprocket on the top.

You’re closing in on the end of this project. All the hard work is currently done, so relax. It’s time to run the wire (if it isn’t currently in position) from the opener to the interior switch. A few of the most recent buttons use radio signals so this action may be excluded. Seek advice from those awful instructions to make sure. The complying with picture reveals a normal circuitry diagram.


Follow the directions pertaining to the exterior switch and hook it up making use of the tiny cable provided in the opener plan.

In your hardware that included the door opener, are 2 digital sensors that require to be mounted near the bottom of the garage door beside the garage door track. These two eyes will “check out” each other and send a message to the opener that it is risk-free to shut the door. If something is within the unseen stream of light passing from among these to the other, then the door will NOT close. These are made use of to keep injuries from taking place when youngsters or small pets are standing where the door will shut. There is a basic cable that affixes from each eye and will require to be set up completely to the opener. Comply with specific guidelines consisted of on how high to install and how to mount these security gadgets. Do not discard them as the door opener will NOT work if these are not linked and straightened properly. Remember they are communicating with each other and the major device for YOUR safety.

Finally, install batteries right into each remote by adhering to the guidelines once more. Connect the unit right into an electrical outlet and test it a number of times.


It is rather typical to need to change a brand-new opener. This does not mean you did anything incorrect. Some doors are much heavier than others and some springs used to help open the garage door are stronger than others. Again follow the instructions closely and readjust the “down” or “up” stress and traveling screws by turning them ideal or left 1/4 turn at a time till you get the door to remain closed or open right.

If you found this “E How To” valuable, I wish to find out about it so I can write various other ideally useful posts. Please let me recognize if this article was useful.

Make sure and examine the elevation of the garage door opening up after mounting a new opener. This is crucial if you are trying to park a van or various other complete size automobile in your garage. You might not have adequate clearance. Also visit troubleshooting common garage door openers for more info.

This entry was posted in Blog.